Brake on the front wheel is the most powerful brake in motorcycle since the center of gravity will move to the front tyre as the front brake is applied. It is clear that excellent front brake condition is the important aspect of motorcycle handling, and the brake lever freeplay plays a major contribution to the brake control since the brake lever is the component in which the driver put on his command to the mechanism.
This post will show you the general procedure of how to adjust motorcycle front brake freeplay, which is you can easily do by yourself at home.
1. Check:
- Brake lever free play [a]. Out of specification → Adjust.
Free play (brake lever): 2 ~ 5 mm (at brake lever end)
2. Adjust:
- Brake lever free play
---------------
Adjustment steps:- Loosen the locknut [1].
- Turn the
How to Adjust Motorcycle Clutch Lever Freeplay
Clutch lever freeplay is the important aspect of clutch control in motorcycle handling. However, some people might not aware about this point in the maintenance. This post will show you the general procedure about how to adjust clutch lever freeplay in motorcycle.
1. Check:
- Clutch cable free play [a] Out of specification → Adjust.
Clutch cable free play (at the end of the clutch lever): 10 ~ 15 mm
2. Adjust:
Clutch cable free play
----------
Adjustment steps:
A. Handlebar side
- Loosen the locknut 1.
- Turn the adjusting bolt 2 in or out until the specified clutch cable free play is obtained.
----------
Adjustment steps:
A. Handlebar side
- Loosen the locknut 1.
- Turn the adjusting bolt 2 in or out until the specified clutch cable free play is obtained.
Turn in Clutch cable free play is
How to Replace Motorcycle Engine Oil (with Pictures)
Replacing the motorcycle engine oil is quite easy. Yet, some people still don't understand how to change their own motorcycle engine oil. So in this post we will show you the step-by-step procedure of replacement and how to check if your work is on the right path.
2. Place a container under the engine oil drain bolt.
3. Remove:
- Engine oil filler bolt
- Engine oil drain bolt [1] (along with the gasket)
- Oil filter element drain bolt [2] (along with
How to Adjust Motorcycle Engine Throttle Cable (with Pictures)
Throttle cable free play is commonly the forgotten part of motorcycle maintenance. Despite of its minor role, throttle cable free play can significantly affect your handling ability. This post shows you the general procedure of throttle cable free play in motorcycle with carburetor.
Prior to adjusting the throttle cable free play, the engine idling speed should be adjusted.
1. Check:
- Throttle cable free play [a]
Out of specification → Adjust.
Free play (throttle cable): 3 ~ 5 mm at throttle grip flange.
2. Adjust:
- Throttle cable free play
---------------------
Adjustment steps:
1. Check:
- Throttle cable free play [a]
Out of specification → Adjust.
Free play (throttle cable): 3 ~ 5 mm at throttle grip flange.
2. Adjust:
- Throttle cable free play
---------------------
Adjustment steps:
How to Adjust Motorcycle Engine Valve Clearance
Valve clearance adjustment should be made with the engine cool, at room temperature. When the valve clearance is to be measured or adjusted, the piston must be at Top Dead Center (T.D.C) on the compression stroke. Below are the general procedure of adjustment.
1. Remove:
- Spark plug
- Tappet cover (intake side) [1]
- Tappet cover (exhaust side) [2]
2. Remove:
- Timing mark accessing screw (with
Valve Clearance Adjustment |
- Spark plug
- Tappet cover (intake side) [1]
- Tappet cover (exhaust side) [2]
2. Remove:
- Timing mark accessing screw (with
Training for a Career in Automotive Service: Which Program should I Choose?
Those interested in a career in auto service can receive training in formal school settings—secondary, postsecondary, and vocational schools; and technical or community colleges, both private and public.
Student Work Experience
There are many ways to gain work experience while you are a student. You may already be involved in one of the following; if not, consider becoming involved in one of these programs. Job Shadowing Program In this program you follow an experienced technician or service writer. The primary objective is to expose you to the “real world,” to see what it takes to be a successful technician or service writer. By job shadowing, you will also become familiar with the total operation of a service department.
Mentoring Program
This program is not the most common program, but it can be one of the most valuable. In a mentoring program, you experience the duties and responsibilities of a technician while you have someone who is successful to use as an expert. Your mentor has agreed to stay in contact with you, to answer questions, and to encourage you. When you have a good mentor,
Student Work Experience
There are many ways to gain work experience while you are a student. You may already be involved in one of the following; if not, consider becoming involved in one of these programs. Job Shadowing Program In this program you follow an experienced technician or service writer. The primary objective is to expose you to the “real world,” to see what it takes to be a successful technician or service writer. By job shadowing, you will also become familiar with the total operation of a service department.
A career possibility for an experienced technician is that of a trainer for the various manufacturers or instructors for an automotive program. |
This program is not the most common program, but it can be one of the most valuable. In a mentoring program, you experience the duties and responsibilities of a technician while you have someone who is successful to use as an expert. Your mentor has agreed to stay in contact with you, to answer questions, and to encourage you. When you have a good mentor,
Ohm’s Law: How to Apply it in Practice on a Vehicle
In 1827, a German mathematics professor, Georg Ohm, published a book that included his explanation of the behavior of electricity. His thoughts have become the basis for the understanding of electricity. He found it takes 1 volt of electrical pressure to push 1 ampere of electrical current through 1 ohm of resistance. This statement is the basic law of electricity and is known as Ohm’s law.
A simple electrical circuit is a load connected to a voltage source by conductors. The resistor could be a fog light, the voltage source could be a battery, and the conductor could be a copper wire.
In any electrical circuit, current (I), resistance (R), and voltage (E) are mathematically related. This relationship is expressed in a mathematical statement of Ohm’s law. Ohm’s law can be applied to
A simple electrical circuit is a load connected to a voltage source by conductors. The resistor could be a fog light, the voltage source could be a battery, and the conductor could be a copper wire.
A simple circuit consists of a voltage source, conductors, and a resistance or load. |
Basics of Electricity: Electricity is Not Magic!
Perhaps the one reason it is difficult to understand electricity is that its action is not usually seen. By knowing what it is and what it is not , you can easily understand it. Electricity is not magic! It is something that takes place or can take place in everything you know. It not only provides power for lights, TVs, stereos, and refrigerators, it is also the basis for the communications between our brain and the rest of our bodies.
The effects of electricity can be seen, felt, heard, and smelled. One of the most common displays of electricity is a lightning bolt. Lightning is electricity—a large amount of electricity! The power of lightning is incredible. Other than lightning, electricity is not normally seen because
Electricity is the flow of electrons from one atom to another. |
Car and Motorcycle Engine Noise Diagnosis
More often than not, an engine malfunction will reveal itself first as an unusual noise. This can happen well before the problem affects the driveability of the vehicle. Problems such as loose pistons, badly worn rings or ring lands, loose piston pins, worn main bearings and connecting rod bearings, loose vibration damper or flywheel, and worn or loose valve train components all produce telltale sounds. Unless the technician has experience in listening to and interpreting engine noises, it can be very hard to distinguish one from the other.
When correctly interpreted, engine noise can be a very valuable diagnostic aid. Always do a noise analysis before
Using a stethoscope helps to identify the source of an abnormal noise. |
Wheel Alignment: Caster/Camber Adjustment
Caster affects steering stability and steering wheel returnability. Zero (0) caster is present when the upper ball joint or top strut bearing and lower ball joint are in the same plane as viewed from the side of the vehicle. Positive caster exists when the upper ball joint or top strut bearing is toward the rear of the vehicle in relationship to the lower ball joint. When the upper ball joint or top strut bearing is toward the front of the vehicle in relationship to the lower ball joint, negative caster is present. If the caster at both wheels is not equal, the vehicle will tend to drift toward the side with the lowest caster.
Camber is the inward or outward tilt of the top of the wheel. Adjusting camber centers the vehicle’s weight on the tire. Proper camber adjustment minimizes
Examples of the screens available on the latest alignment machines. |
Air-Conditioning Performance Testing
Performance testing provides a measure of A/C system operating efficiency. A manifold pressure gauge set is used to determine both high and low pressures in the refrigeration system. The desired pressure readings will vary according to temperature. Use temperature/pressure charts as a guide to determine the proper pressures. At the same time, a thermometer is used to determine air discharge temperature in the passenger compartment.
SERVICE VALVES
System service valves provide the attachment point for the manifold pressure gauge set. They are located in the low and high sides of most A/C systems. Two basic types of service valves were used on R-12 systems: stem and Schrader. R-134a systems have quick-connect fittings. The fittings for the gauges are connected to the system’s fittings. The gauge’s fitting has a knob that is turned in the clockwise direction to open the valve. No refrigerant should leak out when the gauge set is connected.
Stem Valves. The stem valve was sometimes used on twocylinder reciprocating-piston compressors. The service valves are mounted on the compressor head. These valves can be used to
SERVICE VALVES
System service valves provide the attachment point for the manifold pressure gauge set. They are located in the low and high sides of most A/C systems. Two basic types of service valves were used on R-12 systems: stem and Schrader. R-134a systems have quick-connect fittings. The fittings for the gauges are connected to the system’s fittings. The gauge’s fitting has a knob that is turned in the clockwise direction to open the valve. No refrigerant should leak out when the gauge set is connected.
A thermometer is used to determine air discharge temperature in the passenger compartment. |
Air-Conditioning Diagnosis: Noise and Odors on Your A/C system?
Often diagnosis of an A/C system can be done by observing the operation of the system, including listening for noises. When abnormal noises are heard, they can lead to the problem area.
NOISE
Often a customer’s concern is the noise emitted by the A/C system. The following discussion covers the common abnormal noises and their causes.
A typical cabin air filter and housing. |
Often a customer’s concern is the noise emitted by the A/C system. The following discussion covers the common abnormal noises and their causes.
- Clutch Noises. The clutch normally makes a clicking noise when it engages and disengages. This noise will become louder as the clutch wears. Once the clutch is severely worn, it will make a squealing noise when it is engaged. This noise can also result from oil on the clutch. A very loud screech or squeal can indicate a seized compressor. A bent drive pulley also can cause a growling or rubbing noise.
- Hose Noise. The change in pressures in the suction/discharge hoses can set up vibrations that cause sounds to appear from the inside of the vehicle. The noise is typically caused by
How to Convert (Retrofitting) R-12 Air Conditioning System to R-134a
The following guidelines should be followed when converting an older A/C system to R-134a. These guidelines should allow you to provide the customer with a cool vehicle and to meet current legislative mandates.
The guidelines are listed in order and reflect the necessary steps for making this conversion.
A label showing that an R-12 A/C system was converted to R-134a. This must be attached to the vehicle whenever the conversion has taken place. |
- Visually inspect all A/C and heater system components.
- Use a refrigerant identifier to make sure the system only contains R-12.
- Check the system for
Automobile Air-conditioning: REFRIGERANT SAFETY PRECAUTIONS
Air-conditioning (A/C) service, in many ways, is different from service to other parts of the vehicle. Although there are few parts in the system, each component has a specific purpose and service procedure.
R-12 should be stored and sold in white containers, whereas R-134a should be stored in light blue containers. |
That by itself is not a big deal. The challenge with the A/C is how it operates. The system operates on changes of refrigerant pressure. There are many things that can cause the pressure to change; some are part of the system, some are part of the environment, and some of them are faults or bad components in the system.
There are some precautions when you work with refrigerants.
- Always work in a well-ventilated and clean area. Refrigerants are colorless and invisible. Refrigerant is heavier than oxygen and will displace it in a confined area. Avoid breathing the refrigerant vapors. Exposure to refrigerant may irritate your eyes, nose, and throat.
- Refrigerant evaporates quickly when it is exposed to the atmosphere. It will
Automobile Air-conditioning: Service Precautions
A/C systems are extremely sensitive to moisture and dirt. Therefore, clean working conditions are very important. The smallest particle of foreign matter in an A/C system contaminates the refrigerant, causing rust, ice, or damage to the compressor. For this reason, all replacement parts are sold in vacuum-sealed containers and should not be opened until they are ready to be installed in the system. If, for any reason, a part has been removed from its container for any length of time, the part must be completely flushed using only the recommended solvent to remove any dirt or moisture that might have accumulated during storage. If the system has been open for more than 2 minutes, the entire system must be completely evacuated and a new accumulator or desiccant bag must be installed.
It is important to remember that just one drop of water added to the refrigerant will
A late-model air-conditioning system. |
Exhaust Smoke Diagnosis: Evaluating the Engine's Condition
Once the compression, cylinder leakage, vacuum, and power balance tests are performed, further testing can be done to evaluate the engine’s condition. For example, an engine with good relative compression but high cylinder leakage past the rings is typical of a high-mileage worn engine. This engine would have these symptoms: excessive blowby, lack of power, poor performance, and reduced fuel economy.
If comparable compression and leakage test results are found on an engine with comparatively low mileage, the problem is probably
Exhaust analysis. |
If comparable compression and leakage test results are found on an engine with comparatively low mileage, the problem is probably
Fluid Leaks: Evaluating the Engine's Condition
When inspecting the engine, check it for leaks. There are many different fluids under the hood of an automobile so care must be taken to identify the type of fluid that is leaking.
Carefully look at the top and sides of the engine, and note any wet residue that may be present. Sometimes road dirt will
Identification of fluid leaks. |
Carefully look at the top and sides of the engine, and note any wet residue that may be present. Sometimes road dirt will
How to Change the Oil and Oil Filter (with Detailed Demonstration Pictures)
Maintenance
Perhaps the PM service that is best known to the public is changing the engine’s oil and filter. Because oil is the lifeblood of an engine, it is critical that the oil and filter are changed on a regular basis. These photo sequence show the steps involved in changing the engine oil and oil filter. Whenever doing this, make sure the oil is the correct rating for the vehicle.
1. Always make sure the vehicle is positioned safely on a lift or supported by jack stands before working under it. Before raising the vehicle, allow the engine to run awhile. After it is warm, turn off the engine.
Perhaps the PM service that is best known to the public is changing the engine’s oil and filter. Because oil is the lifeblood of an engine, it is critical that the oil and filter are changed on a regular basis. These photo sequence show the steps involved in changing the engine oil and oil filter. Whenever doing this, make sure the oil is the correct rating for the vehicle.
1. Always make sure the vehicle is positioned safely on a lift or supported by jack stands before working under it. Before raising the vehicle, allow the engine to run awhile. After it is warm, turn off the engine.
Mass and Weight, What's the Difference?
Mass is the amount of matter in an object. Weight is a force and is measured in pounds or kilograms (1,000 grams). Gravitational force gives the mass its weight. As an example, a spacecraft can weigh 500 tons (one million pounds) here on earth where it is affected by the earth’s gravitational pull. In outer space, beyond the earth’s gravity and atmosphere, the spacecraft is nearly weightless but its mass remains unchanged.
The difference in weight of a space shuttle on earth and in space. |
Preparing Your Cover Letter: Seeking and Applying for Employment
A cover letter should be sent with every resume you mail, e-mail, fax, or personally deliver. A cover letter gives you a chance to point out exactly why you are perfect for the job. You should not send out the same cover letter to all potential employers. Adjust the letter to match the company and position you are applying for.
Yes, this means a little more work, but it will be worth it. Address the letter to the person doing the hiring. Do NOT use “Dear Sir, Dear Madam, or To Whom it may concern.” If the job posting does not give the hiring person’s name, you can normally find who to send the resume to by calling the employer and asking to whom to address your cover letter. You can also try checking other business information sites to determine the name of the person conducting the interviewing.
Yes, this means a little more work, but it will be worth it. Address the letter to the person doing the hiring. Do NOT use “Dear Sir, Dear Madam, or To Whom it may concern.” If the job posting does not give the hiring person’s name, you can normally find who to send the resume to by calling the employer and asking to whom to address your cover letter. You can also try checking other business information sites to determine the name of the person conducting the interviewing.
An example of a cover letter that can be sent with the resume. |
Preparing Your Resume: Seeking and Applying for Employment
Becoming employed, especially in the field in which you want a career, involves many steps. As with many things in life, you must be adequately prepared before taking the next step toward employment. This discussion suggests ways you can prepare and what to expect while taking these steps.
Your resume and cover letter are your own personal marketing tools and may be an employer’s first look at you. Although not all employers require a resume, you should prepare one for those that do. Preparing a resume also forces you to look at your qualifications for a job. That alone justifies having a resume.
Keep in mind that although you may spend hours writing and refining your resume, an employer may only take a minute or two from his or her busy schedule to look it over. With this in mind, put together a resume that tells the employer who you are in such a way that he or she wants to interview you.
Your resume and cover letter are your own personal marketing tools and may be an employer’s first look at you. Although not all employers require a resume, you should prepare one for those that do. Preparing a resume also forces you to look at your qualifications for a job. That alone justifies having a resume.
Keep in mind that although you may spend hours writing and refining your resume, an employer may only take a minute or two from his or her busy schedule to look it over. With this in mind, put together a resume that tells the employer who you are in such a way that he or she wants to interview you.
How to Lift and Carry Heavy Objects
Often technicians or workers will need to move something that is heavy. Knowing how to lift these heavy things can save your career. When lifting any object, follow these steps:
Figure A. Use your leg muscles— never your back—to lift heavy objects. |
- Place your feet close to the object. Position your feet so you will be able to maintain a good balance.
- Keep your back and elbows as straight as possible. Bend your knees until your hands reach the best place to get a strong grip on the object (Figure A).
- If the part is in a cardboard box, make sure the box is in good condition. Old, damp, or poorly sealed boxes will tear and the part will fall out.
- Firmly grasp the object or container. Never try to change your grip as you move the load.
- Keep the object close to your body, and lift it up by straightening your legs. Use your leg muscles, not your back muscles.
Electrons and Protons in the Atom
Although there are any number of possible methods by which electrons and protons might be grouped, they assemble in specifi c atomic combinations for a stable arrangement. (An atom is the smallest particle of the basic elements which forms the physical substances we know as solids, liquids, and gases.) Each stable combination of electrons and protons makes one particular type of atom. For example, Fig. 1–2 illustrates the electron and proton structure of one atom of the gas, hydrogen. This atom consists of a central mass called the nucleus and one electron outside. The proton in the nucleus makes it the massive and stable part of the atom because a proton is 1840 times heavier than an electron.
In Fig. 1, the one electron in the hydrogen atom is shown in an orbital ring around the nucleus. To account for the electrical stability of the atom, we can consider the electron as spinning around the nucleus, as planets revolve around the sun. Then the electrical force attracting the electrons in toward the nucleus is balanced by the mechanical force outward on the rotating electron. As a result, the electron stays in its orbit around the nucleus.
Figure 1. Electron and proton in hydrogen (H) atom. |
Steel Manufacture: Ironmaking, Steelmaking, Continuous Casting, and Rolling/Forging
In most of the world, steel is manufactured by integrated steel facilities that produce steel from basic raw materials, i.e., iron ore, coke, and limestone. However, the fastest growing segment of the steel industry is the “minimill” that melts steel scrap as the raw material. Both types of facilities produce a wide variety of steel forms, including sheet, plate, structural, railroad rail, and bar products.
Eye Protection: How to Work Safely in the Shop
To protect yourself from injuries, you need to wear personal protective equipment (PPE), dress appropriately, work professionally, and correctly handle tools and equipment. PPE are items such as safety glasses, uniforms, and safety boots or shoes that help protect you while working in the shop.
Teori Dasar Cara Kerja Baterai: Reaksi Elektrokimia
Baterai adalah alat elektro kimia yang dibuat untuk mensuplai listrik ke sistem starter, sistem pengapian, sistem penerangan, dan komponen kelistrikan lainnya. Alat ini menyimpan listrik menyimpan listrik dalam bentuk energi kimia yang akan dikeluarkan bila diperlukan, mensuplai ke masing-masing sistem yang memerlukannya.
Karena dalam proses baterai kehilangan energi kimia, maka alternator mensuplainya kembali ke
Teori Dasar Rangkaian Kontrol Arus Listrik
Video ini menjelaskan tentang konfigurasi kontrol beban dalam rangkaian listrik otomotif.
Ada dua jenis sirkuit kontrol, yaitu Source Control Circuit dan Ground Control Circuit. Walaupun berbeda susunan, keduanya memiliki peran yang sama.
Switching devices berperan dalam mengatur arus dalam sirkuit kelistrikan. Switching devices diantaranya adalah
Ada dua jenis sirkuit kontrol, yaitu Source Control Circuit dan Ground Control Circuit. Walaupun berbeda susunan, keduanya memiliki peran yang sama.
Switching devices berperan dalam mengatur arus dalam sirkuit kelistrikan. Switching devices diantaranya adalah
Cara Mencari Korsleting Listrik DC pada Mobil dan Sepeda Motor (dengan EWD)
Video ini menjelaskan tentang pengetahuan dasar korsleting listrik beserta cara mencari sumber atau titik korsleting pada rangkaian kelistrikan kendaraan dengan menggunakan Electrical Wiring Diagram.
Korsleting listrik atau short circuit adalah kejadian di mana listrik mengalir langsung menuju ground tanpa melalui load, sehingga arus listrik yang mengalir melebihi ukuran yang semestinya.
Korsleting listrik atau short circuit adalah kejadian di mana listrik mengalir langsung menuju ground tanpa melalui load, sehingga arus listrik yang mengalir melebihi ukuran yang semestinya.
Cara Kerja Motor Starter Elektrik Konvensional
Untuk menghidupkan mesin diperlukan gaya dari luar untuk penggerakkan awal siklus kerja (hisap, kompresi, usaha, buang). Umumnya, saat ini mobil dan sepeda motor menggunakan electric starter motor sebagai penggerak mula. Starter motor menggunakan energi listrik yang tersimpan di baterai sebagai sumber energi, mengubahnya menjadi energi mekanik dalam bentuk rotasi.
Motor starter yang digunakan pada mobil dilengkapi dengan
Motor starter yang digunakan pada mobil dilengkapi dengan
Sistem Pengisian (Charging System) Konvensional : Komponen, Fungsi dan C...
Video ini menjelaskan tentang Sistem Pengisian (Charging System) Konvensional.
#Bagian-1: Cara kerja pada saat kunci kontak ON dan mesin mati.
Fungsi baterai pada mobil adalah untuk mensuplai kebutuhan listrik pada komponen-komponen kelistrikan, seperti motor starter, lampu, dan penghapus kaca. Namun demikian, kapasitas baterai sangatlah terbatas, sehingga tidak mampu mensuplai listrik secara terus-menerus.
Dengan demikian, baterai harus selalu terisi penuh agar dapat mensuplai kebutuhan listrik setiap waktu saat diperlukan oleh tiap komponen kelistrikan.
#Bagian-1: Cara kerja pada saat kunci kontak ON dan mesin mati.
Fungsi baterai pada mobil adalah untuk mensuplai kebutuhan listrik pada komponen-komponen kelistrikan, seperti motor starter, lampu, dan penghapus kaca. Namun demikian, kapasitas baterai sangatlah terbatas, sehingga tidak mampu mensuplai listrik secara terus-menerus.
Dengan demikian, baterai harus selalu terisi penuh agar dapat mensuplai kebutuhan listrik setiap waktu saat diperlukan oleh tiap komponen kelistrikan.
Jurnal Pendidikan Vokasi: Teknik Otomotif
Halo online learners Sekolah Online Teknik Otomotif!
Artikel penelitian kami telah tersedia untuk diunduh secara gratis di link berikut ini: https://journal.uny.ac.id/index.php/jpv/article/view/17356/10405
atau pratinjau abstraknya di link berikut:
https://journal.uny.ac.id/index.php/jpv/article/view/17356
• Vol 8, No 1 (2018): February
• Title: Development of YouTube Integrated Google Classroom Based E-Learning Media for the Light-Weight Vehicle Engineering Vocational High School
• http://dx.doi.org/10.21831/jpv.v8i1.17356
• Authors: Willy Prastiyo(1*), As’ari Djohar(2), Purnawan(3) | (1), (2), (3) Departemen Pendidikan Teknik Mesin, Fakultas Pendidikan Teknologi dan Kejuruan, Universitas Pendidikan Indonesia (*) Corresponding Author
ISSN 2088-2866 (print) || ISSN 2476-9401 (online) | [ Open Access and Accredited by Ministry of Research and Technology of Higher Edcuation of Indonesia ]
Artikel penelitian kami telah tersedia untuk diunduh secara gratis di link berikut ini: https://journal.uny.ac.id/index.php/jpv/article/view/17356/10405
atau pratinjau abstraknya di link berikut:
https://journal.uny.ac.id/index.php/jpv/article/view/17356
• Vol 8, No 1 (2018): February
• Title: Development of YouTube Integrated Google Classroom Based E-Learning Media for the Light-Weight Vehicle Engineering Vocational High School
• http://dx.doi.org/10.21831/jpv.v8i1.17356
• Authors: Willy Prastiyo(1*), As’ari Djohar(2), Purnawan(3) | (1), (2), (3) Departemen Pendidikan Teknik Mesin, Fakultas Pendidikan Teknologi dan Kejuruan, Universitas Pendidikan Indonesia (*) Corresponding Author
ISSN 2088-2866 (print) || ISSN 2476-9401 (online) | [ Open Access and Accredited by Ministry of Research and Technology of Higher Edcuation of Indonesia ]
Subscribe to:
Posts (Atom)
Popular Courses
- Wheel Alignment: Caster/Camber Adjustment
- Fungsi dan Cara Kerja Ackermann Steering Geometry pada Kendaraan
- Definisi dan Penghitungan Piston Displacement (berdasarkan Spesifikasi Mesin)
- Analisis dan Tutorial Cara Penyetelan Celah Katup Mesin Isuzu 4JB1 Diesel Engine
- Penjelasan Daya Indikator dan Kurva Daya Efektif pada Motor/Mesin